Automation Engineer/Instrument Supervisor/Material Inspector-Instrumentation/Shift Instrument Technician

Automation Engineer–

Instrument Supervisor–

Material Inspector-Instrumentation–

Shift Instrument Technician-

Job Description for Instrument Engineer (Automation Engineer)

Minimum Qualification/Experience Minimum

Qualification:

Instrument and electronics Engineering Bachelor degree with 4 years added experience.

Minimum Experience:

4 years minimum experience (2 years of which must be in maintenance environment).

Primary Duties and Responsibilities include but not limited to: Duties: -

 To render technical support, for all instrumentation and analyser equipment, to the Maintenance Division. Fault

finding and problem solving, suggesting operational changes to improve plant / equipment reliability and integrity.

 Perform Root Cause Failure Analysis on failed equipment.

 Ensure findings and actions from Root Cause Analysis instituted at the site.

 Develop and Implement proven equipment maintenance strategies.

 Review and comment on design and engineering work of engineering contractors and suppliers.

 Coordinating the turnaround activities of the relevant discipline.

Responsibilities: -

 Develop reliability systems to ensure reliable equipment.

 Optimization of electrical control and fault finding on problem areas.

 Identify and solve problems on electrical systems and implement changes as required.

 Ensure system integration between different systems and high level of integrity is maintained at all times.

 Writing and update of Electrical narratives and procedures for testing. Also update documentation as and

when required.

 Develop and implement engineering changes for Electrical systems.

 Root cause analysis methodology to be used for incident investigations.

 Work closely with maintenance teams (Supervisors and Technicians).

Job Specific Knowledge:

 Instrumentation

 Coordinate with and as required, support other groups such as Maintenance, Analyser, Laboratory, Production, MES

and Process

 Monitor all Maintenance data for the equipment associated with DCS, ESD, Woodward governor, CCC, Turbo log,

Machine Monitoring system and Asset Management System.

 Coordinate with the appropriate Company Maintenance and Operations Representative as required to establish

work priorities based on Operations requirements.

 Review back up procedures and updating the system.

 Review equipment history and performance, contributes to plant failures investigation and proposes

recommendations for improvement.

 Participate and assist as required in the upgrading of Maintenance procedures to meet changing or additional

requirements.

 Prepare/compile Work and Maintenance instructions for all related Control Room Equipment.

 Investigate equipment failures or problems that arise during the commissioning and startup phase and liaise

with the Project and the EPC Contractor to resolve the issues.

 Review control system design issues raised by Operations /Maintenance personnel and make recommendations for

remedial action.

 Coordinate Punch Listing and other commissioning activities related to Control Room Equipment.

 Ensure all DCS and control room equipment meet specification and is fit for purpose prior to handover.

 Review and process approved daily job requests received from specific process area. This includes discussing and

determining priorities in conjunction with the appropriate department in the Company, making detailed assessment

of resources, material and logistic requirements.

 Deal with emergency requests immediately, providing technical advice, coordinating with other sections,

allocating manpower and following up work progress.

 Review if required Software configuration and attend Factory Acceptance Tests (FAT) if required.

 Attend Site Acceptance Tests (SAT) Ensure safety of personnel and equipment through compliance with the

company’s Environmental Health and Safety Procedures, as well as occupational health and safety regulations;

similarly compliance with security.

 Knowledge on Process Control.

 Knowledge on Hazardous area requirements.

 Knowledge on Networking

 Knowledge on Database Management System.

 Knowledge on software and hardware Maintenance of Distributed Control system – DCS

- Foxboro

 Knowledge on software and hardware Maintenance of Programmable Logic Controller

– PLC - TRICONEX

 Knowledge on Safety Integrity Levels and ratings of loops – SIL

 Knowledge on software and hardware Maintenance of Compressor Anti Surge Control System – CCC and Turbo log

Controllers

 Knowledge on software and hardware Maintenance of Turbine Speed Controllers –

Woodward

 Knowledge on Tuning and Optimization of Control loops.

 Knowledge on software and hardware Maintenance of Asset Management System –

Avantis Pro, Field Device Tools

 Knowledge on software and hardware Maintenance of Vibration Monitoring systems –

Bentley Nevada

 Knowledge on Intrinsic Safety requirements and instruments.

 Knowledge on Industrial Communication Protocols – Modbus, Fieldbus, RS 232, RS 485, TCP/IP, Object Linking and

Embedding for Process Control (OPC).

Job Description for Instrument Supervisor

 Technical Diploma is the minimum qualification.

 Minimum 5-7-year experience in which 2 years as supervisor in Petrochemical / Oil / Gas industries.

 Ex competency Certification as per IEC 60079 part 14 and 17 listed below with 2 years’

post certification experience required for all selected candidates.

Ex01-Preparation &Installation of Ex’d’, Ex’e’, Ex‘n’ and Ex ‘p’ system . Ex02-Inspection

&Maintenance of Ex ‘d’ Ex’e’, Ex‘n’ and Ex ‘p’ system . Ex03 - Preparation &Installation of Ex

‘i’ System.

Ex04 - Inspection &Maintenance of Ex ‘i’ System.

 Gulf experience preferable (not mandatory)

 To be the frontline person leading the team of technicians to execute the assigned jobs as per ORYX GTL work

specifications with focus on safety, timely completion availability.

 Knowledge of field instruments used in Petrochem, Oil, gas industries.

 Interpersonal skills to work in close coordination with ORYX Supervisors/Engineers.

 Liaison with planning, services and production departments.

Job Description for Material Inspector – E&I

Minimum Qualification/Experience